Innotech Genesis V4 System Uživatelský manuál Strana 8
- Strana / 115
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Installation Instructions for Innotech Genesis Systems
Edition: 011100
iv
TABLE OF CONTENTS – (Continued)
SECTION/PARAGRAPH PAGE
A-4.2.9. Genesis II Non-Isolated Comms. ...................................................A-14
A-4.2.9.1. Hazardous Earth-Connections. ................................................A-16
A-4.2.9.2. Use of GENII POLY SWITCH Boards. ..................................A-18
A-4.2.10. Genesis II Isolated Comms. ............................................................A-20
A-4.2.11. Genesis II Comms. Isolated by Repeater. ....................................A-22
A-4.2.12. GENII MPI with Non-Isolated Comms. ........................................A-24
A-4.3. CABLE CONNECTION PROCEDURES. .................................................A-25
APPENDIX B- DATA SHEETS. ........................................................................................B-1
B-1. INTRODUCTION. ..................................................................................................B-1
LIST OF ILLUSTRATIONS
FIGURE PAGE
2-1. Digital Controller Plastic Lid Clamping Details. .......................................................2-2
2-2. Digital Controller Dimensions. ..................................................................................2-2
2-3. Genesis II Mid Points Controller. ..............................................................................2-3
2-4. Typical Local Expansion Module. .............................................................................2-4
2-5. Typical Remote Expansion Module. ..........................................................................2-5
2-6. GENII RMI Remote Module Interface. .....................................................................2-6
2-7. GENII CS Control Station Module. ...........................................................................2-6
2-8. Typical Enclosure Layout. .........................................................................................2-8
2-9. DIN Rail Dimensions. ................................................................................................2-9
2-10. Digital Controller Display, Viewing Angles. .............................................................2-9
2-11. Typical Remote System Layout. ................................................................................2-11
3-1. Computer-Generated Wiring Diagram, Example. .....................................................3-3
3-2. Genesis II Digital Controller Input/Output Terminals. ..............................................3-4
3-3. Driving Multiple Solid-State Relays. .........................................................................3-8
3-4. Genesis II MPC Input/Output Terminals. ..................................................................3-10
3-5. Genesis I Digital Controller Input/Output Terminals. ...............................................3-13
3-6. Analogue Input Module. ............................................................................................3-15
3-7. Analogue Input Module Wiring, Example. ................................................................3-16
3-8. Digital Input Module. .................................................................................................3-17
3-9. Digital Output Module. ..............................................................................................3-18
3-10. RS485 Comms Cable Connections. ...........................................................................3-21
3-11. RMI Remote Module Interface. .................................................................................3-22
3-12. AI REM Analogue Input Module. .............................................................................3-22
3-13. AO REM Analogue Output Module. .........................................................................3-23
3-14. CS REM Control Station Module. .............................................................................3-25
3-15. MP REM Multipoint Module. ...................................................................................3-26
3-16. MP REM, Digital Input Wiring. ................................................................................3-28
- Innotech 1
- PROPRIETARY 3
- TRADEMARK 3
- TABLE OF CONTENTS 5
- LIST OF ILLUSTRATIONS 8
- LIST OF TABLES 10
- GENESIS II 18
- DIGITAL INPUT MODULE 18
- GEN II AI REM 19
- REMOTE MODULE INTERFACE 20
- D.I.M. D.I.M. D.O.M. D.O.M 22
- SIDE VIEW TOP VIEW 23
- 90 DEGREES 23
- GENESIS II DDCINNOTECH 29
- GEN II MPC 36
- ANALOGUE INPUT MODULE 41
- 3233 343536 42
- DIGITAL OUTPUT MODULE 44
- ++ = Positive Comms Line 46
- −− = Negative Comms Line 46
- A1 A2 A3 A4 A5 A6 48
- ABCDEFGH I J 50
- DI 1 DI 2 DI 3 DI 4 DI 5 53
- • C+ = RS 485 (+) Signal 54
- • C- = RS 485 (-) Signal 54
- • SHLD = Comms cable shield 54
- COMMS DIGITAL INPUTS SENSOR 55
- COMMISSIONING 56
- 4-1.2.2 60
- 4-1.2.2.1 60
- JUMPER WIRE 61
- 4-1.2.2.2 62
- SWITCH CLOSED 63
- SWITCH OPEN 63
- GENII DI REM 63
- 4-1.2.3 64
- EXTERNAL 65
- 4-1.2.4 67
- ANALOGUE 69
- CONDITIONERS 69
- 4-1.2.4.2 70
- 4-1.2.4.3 72
- 4-1.2.5 72
- 4-1.4.1 74
- 4-1.4.2 74
- 4-1.4.3 75
- INNOTECH 76
- 4-1.7.1 78
- 4-1.7.2 79
- 4-1.7.2.1 79
- Example A 84
- Example B 84
- Zone A Zone B 85
- Zone BZone A 85
- 1234- - - 29 30 31 32 86
- 1 234- - - 29 30 31 32 86
- 1 234- - - -29 30 31 32 86
- Pin Strip 90
- BOTTOM EDGE OF BOTTOM BOARD 90
- Screen1 2 100
- Isolated 101
- 89 90 91 92 93 107
- MPI With Isolated RS485 108
- Comms Cables for Port 2 108
- Comms Cables for Port 1 108
- Edition 011100 109
- APPENDIX B- DATA SHEETS 110
Související produkty a manuály pro Software Innotech Genesis V4 System
Software Innotech iSEA Uživatelský manuál
(44 stránky)
(44 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce